14 products found. Go to page:
|
|
|
 | | | Loctite SI 5699 80 ml | €24,59 Add to cart | | Loctite SI 5699 80 ml
for engine cases
Designed for High-Torque applications.
Sensor safe, low odor, non corrosive.
Has outstanding oil resistance and is guaranteed not to leak. Works in the temperature range of -75°F to 625°F (-60°C to 330°C),
resists auto and shop fluids and is vibration ... | |
|
|
|
 | | | Buell Sportster Pinion gear locker tool XB | €58,00 Add to cart | | Buell Sportster Pinion gear locker tool XB
Use tool to lock pinion gear when torquing the pinion
nut. Tool is simple to use, just align underneath
gear and screw into case.
for all Buell Tube frame models 2000-2002for all Buell Xb models 2003-2007
for all Sporster models 2000-2016
do not use impact tools !!!
| |
|
|
|
 | | | Buell XB and Buell 1125 axle tool | €10,25 Add to cart | | Axle tool for all Buell XB 9/12 and all Buell 1125R and 1125CR models,very usefulltool for your tool box.
For all XB and 1125 front and rear wheel and Swing arm axles 2003-2010
size 22mm ( 7/8 ) with 1/2 inch connection
| |
|
|
|
 | | | Buell Suspension tool Front and Rear | €635,00 Add to cart | | Buell Suspension tool for Front Fork and and RearSuspention disassembeling.All in one Suspention tool.
USed for All Buell models, all Sportster models and all XR1200 models.
The best solution for the disassembling of the springs from mono or standard rear shock absorbers, or replace springs and cartridges from front f... | |
|
|
|
 | | | Cable luber TM | €16,70 Add to cart | | Cable Luber
This tool is used to inject lubricant into any mechanical cable housing. The tool clamps over your cable housing and inner cable
allowing you to connect an aerosol lube can of cablelube to this luber tool.
Spray until the lube runs out the other end of cable housing.
For all Buell , Sportster and XR1200 ... | |
|
|
|
 | | | Hydraulic Brake Bleeder | €19,00 Add to cart | | The Hydraulic brake bleeder, makes bleeding your brakes a one-person job at home.
Will not bleed air from a dry system.
This Brake Bleeder is a one-way check valve. This tool allows air andbrake fluid to escape, but will not allow air to re-enter the system.
Note: This tool will notbleed air from a dry system, for ... | |
|
|
|
 | | | Receptable extractor 6 in 1 ALDL, pack-con 1763 | €27,00 Add to cart | | Receptable extractor 6 in 1 ALDL, pack-con , Weather sealed 1763
Easily remove an assortment of harnessstyle receptacle pins with either ofthese 6-in-1 tools.
Designed for automobiles,we have found these to work equally well on allBuell models XR1200 and Sportster.
Use on ALDL, Pack-Con, and weather sealed connectors... | |
|
|
|
 | | | TM Buell Rear shock tool for preload adjustment | On request | | The Twin Motorcycles tool for the Buell rear shock preload adjustment
Can be used for all TM tube frame rear shocks on all Buell Tube models to adjust preload.
Can be used for all Buell XB rear shocks to adjust preload.
And for most other shock absorbers that has a preload adjuster.
| |
|
|
|
 | | | O2 sensor tool | €20,25 Add to cart | | Snap-on O2 sensor tool
3/8 inch Drive, to remove the O2 sensor with out roating the engine on Xb Models
O2 sensor can be reached on Xb models after removing the rear shock absorber and cooling fan
( bike should be very good supported before you remove the rear shock absorber )
can also be used with hard to reach... | |
|
|
|
 | | |
|
All prices are excl. VAT.
