You are here:  Buell Service & Maintenance

Buell 1125R/CR 09-10 burned stator fixing kit

Product number:TM1125Statorkit  

Price excl. VAT:€ 520,37
 
 
Product description

Only Buell 1125R and 1125 CR 2009 -2010 models

With these Twin Motorcycles Parts and tool you can fix your burned out Buell 1125 Stator for good.

This kit contains the following parts:

Product numberPart name
093447301125 2008-2010 Ignition cover gasket1x
21120989Buell 1125 models 2009-2010 replacement stator1x
CD0032.1AMABuell 1125 R/CR Rotor nut 2008-20101x
TMTOOL001Buell 1125 R/CR TM Crank TDC locking tool1x
1125RotoroiljetBuell 1125R/CR Rotor upgrade with oil jet1x
50301120018Buell 1125R/CR Seal ring oil drain right side1x

We highly recommand to use high them silicon gasket to keep the stator wire in place. look HERE

as a adition you can add the Mosfet plug & play regulator to your order 



 The Modified rotor is based as core exchange ! YOU NEED TO SEND US THIS PART, For modification

Send your and rotor to

Twin Motorcycles bv

Edisonweg 44, 3404 LD IJsselstein  

The Netherlands

 

PLEASE PUT REPAIR EXCHANGE PART ON THE SHIPMENT OR WE LET YOU PAY THE INPORT TAX

On arrival they will be inspected if they can be returned  in the exchange pool, and a modified rotor will be shipped to you with the rest of the parts in the kit.

When your Rotor is dammaged or you specify you want your own Rotor to be modified, we will send out your rotor to be modified, this will take +/- 7 days

Special tools needed; high socket size 32 , Torque bar capable for 295 ft/lbs ( 400 Nm )

OUR EXPERIENCE IS TO KEEP THIS AS CHEAP AS POSSIBLE, SHIPPING CAN COST YOU ABOUT 6 WEEKS IN TOTAL ESPECIALY OVERSEAS.

TO RECEIVE THE PARTS DEPENDING ON WHERE YOU LIVE AND HOW QUICK THE POST AND CUSTOMS IS.

Installation 1125 Rotor / Nut  ( update tightening procedure )

Note Crank Locking tool is already in position
1.     Match the double tooth spline on the crankshaft with the gap in splines.
        in the rotor hub and slide the flywheel hub onto the crankshaft
2.    Press the flywheel onto the starter gear.
3.    Rotate the starter gear and the freewheeling gear until the teeth mesh
4.    Clean the threads of the crankshaft and crankshaft nut ( ALWAYS USE A NEW NUT ) with brake cleaner

Note Where LOCTIDE 272 ( red ) is unavailable , Use LOCTIDE 278 ( red )
5.    Install the flywheel nut
a.     Apply LOCTITE 272 ( red )  to the threads and the mating face off the crankshaft nut.
b.    Tighten to 285 NM ( 210 ft-lbs )
c.    Back off the nut counter clockwise approximately 720 degrees
d.    Tighten to 285 NM ( 210 ft- lbs )
e.    Back off the nut counter clockwise approximately 720 degrees
f.    Final tighten to 400 NM ( 295 ft-lbs )

6.    Remove the crank shaft locking tool
7.    Install the plug and tighten to 15 Nm ( 11 ft-lbs )
 

Buell Parts
Buell onderdelen
pièces buell
أجزاء بويل
Buell teile
ビューエルパーツ
Partes buell
Buell части

Related products
» BEARING
» Fuel filter, 1/4 connection
» Buell, choke cable carburator enrichner ( choke )
» Buell XB and 1125 , Swingarm pivot Shaft
» Buell All XB models Gasket Clutch cover
» Buell XB 9/12 K&N Performance Oil filter KN-177
» CHIN FAIRING KIT left (thrust blue) FX
» Buell, bracket pass. footpeg left XB fluid silver