You are here:  Buell Electronics » 1125R

TM Buell 1125R-CR 09-10 BURNT STATOR FIX


Product number:20-B112H- worden niet meer gemaakt
Price excl. VAT:€ 277,00
 

Also available:
» TM Buell 1125R-CR 09-10 BURNT STATOR FIX




 
Product description

WORDEN NIET MEER GEWIKKELD.. NIEUWE stattor verkopen

 

 

This is for all the Buell 1125R and 1125CR 2009-2010 riders with a stator problem. We solved the problem. and we have a core Rotor with oil modification developed to.

Rebuilt Hot Shot Buell Stator:

*This stator is wound with 240 degrees C wire (vs. 200 degrees C stock).

Core return required in advance

**Before installing this rebuilt stator, be sure to get the upgraded version of the Buell rotor. Otherwise stators will continue to burn & will not be covered under warranty.

we still ask you to ship the old part as core replacement to us before we send you out the replacement units

Also highly recommanded to buy ;

Rotor with oil jet modification

Timing cover Gasket R0008.1AM

New Rotor Nut CD0032.1AMA

Crank shaft locking tool 

Loctite 272

not always needed, but advised for original exhaust

Exhaust gaskets 2x
 

NOTE !!!, do not cut the wires on your stator, and leave seals and wire harness in place.

please contact us, if the wires are cut , it will mean we need to send your Stator out for re wiring, and this will take longer to fix !!!

Here is the movie how to remove your damaged stator

And here is the movie how to use our cranck locking tool

and here you can buy our cranck locking tool

 
Related products
» BEARING
» Fuel filter, 1/4 connection
» Buell, choke cable carburator enrichner ( choke )
» Buell XB and 1125 , Swingarm pivot Shaft
» Buell All XB models Gasket Clutch cover
» Buell XB 9/12 K&N Performance Oil filter KN-177
» CHIN FAIRING KIT left (thrust blue) FX
» Buell, bracket pass. footpeg left XB fluid silver
 
Images

 


--

 we highly recommand to use high them silicon gasket to keep the stator wire in place. look HERE

 

Installation 1125 Rotor / Nut  ( update tightening procedure )

Note Crank Locking tool is already in position
1.     Match the double tooth spline on the crankshaft with the gap in splines.
        in the rotor hub and slide the flywheel hub onto the crankshaft
2.    Press the flywheel onto the starter gear.
3.    Rotate the starter gear and the freewheeling gear until the teeth mesh
4.    Clean the threads of the crankshaft and crankshaft nut ( ALWAYS USE A NEW NUT ) with brake cleaner

Note Where LOCTIDE 272 ( red ) is unavailable , Use LOCTIDE 278 ( red )
5.    Install the flywheel nut
a.     Apply LOCTITE 272 ( red )  to the threads and the mating face off the crankshaft nut.
b.    Tighten to 285 NM ( 210 ft-lbs )
c.    Back off the nut counter clockwise approximately 720 degrees
d.    Tighten to 285 NM ( 210 ft- lbs )
e.    Back off the nut counter clockwise approximately 720 degrees
f.    Final tighten to 400 NM ( 295 ft-lbs )

6.    Remove the crank shaft locking tool
7.    Install the plug and tighten to 15 Nm ( 11 ft-lbs )
 

Buell Parts
Buell onderdelen
pièces buell
أجزاء بويل
Buell teile
ビューエルパーツ
Partes buell
Buell части