Articles & photos
Back |
5-4-2018, injector testing, XB, 1125 fork seal, XB
23-7-2018 - What did we do Today: 5-4-2018, injector testing, Buell X12B neutral, Buell 1125R fork seal and make it better stacks and fuel mapping, Buell XB12 dash plate
we have a injector testing and cleaning service.. LOOK HERE
dirty , but not to bad — bij Twin Motorcycles Buell Support forever.
we will replace the inlet filters to — bij Twin Motorcycles Buell Support forever.
first tes.. spray pattern looks good , and the injector are not leaking under pressure — bij Twin Motorcycles Buell Support forever.
resistance is ok — bij Twin Motorcycles Buell Support forever.
so testing the flow — bij Twin Motorcycles Buell Support forever.
also good.. nothing wrong with these — bij Twin Motorcycles Buell Support forever.
we will clean theme any way in the ultrasone and leaving the feeds on the injectors so the fluid also comes inside and — bij Twin Motorcycles Buell Support forever.
nice and clean — bij Twin Motorcycles Buell Support forever.
special puller for the inlet filters — bij Twin Motorcycles Buell Support forever.
only to be distrucfively removed — bij Twin Motorcycles Buell Support forever.
new filter need to be pressed in,and with new O-rings the injectors can go back to the customer — bijTwin Motorcycles Buell Support forever.
xb with neutral problem while standing still and engine running.. after adjusting clutch and primairy chain.. going to try a thinner fluid to see if the fluid friction in the clutch is the problem — bij Twin Motorcycles Buell Support forever.
fluid looks spent — bij Twin Motorcycles Buell Support forever.
the gearbox fuild we used with our race XB RR and adviced with aftermarket high friction clutch plate sets — bij Twin Motorcycles Buell Support forever.
my 10 o clock arrived, very nice 08 1125 R — bijTwin Motorcycles Buell Support forever.
leaking fork seal — bij Twin Motorcycles Buell Support forever.
so wheel out — bij Twin Motorcycles Buell Support forever.
and taking the legs out — bij Twin Motorcycles Buell Support forever.
some protection on the cap nuts — bij Twin Motorcycles Buell Support forever.
taking the seals out can be a crime with these legs.. a seal remover can help — bij Twin Motorcycles Buell Support forever.
little corrosion spot, just in the travel of the seal, will take off the sharp edges.. with some scotchbrite — bij Twin Motorcycles Buell Support forever.
new seals in and mounting the legs — bij Twin Motorcycles Buell Support forever.
set eh rebound adjuster needle so , closed is flat and points alinged — bij Twin Motorcycles Buell Support forever.
legs in.. and caliper bolts with a drop loctite — bijTwin Motorcycles Buell Support forever.
wheel axle to tq — bij Twin Motorcycles Buell Support forever.
pushing down the front end to set the legs on teh axle — bij Twin Motorcycles Buell Support forever.
other thing.. is this a good thing.?? eeehhh no.. only takes the fuel and tps and douse not take feedback from O2 sensor, and piggy back with exstra conenctions is always more problems — bij Twin Motorcycles Buell Support forever.
leave the air ilter in if you pull of the airbox.. not to dump the loose debris in the throttle bodie — bijTwin Motorcycles Buell Support forever.
stock rings removed — bij Twin Motorcycles Buell Support forever.
removing the throttle control cable ( emmisions ) — bij Twin Motorcycles Buell Support forever.
and lock wire the throttle cams to getter. other wise you will have big problems high rpm engine braking ( the throttle will close on its own and will not responce to the throttle movement ) — bij Twin Motorcycles Buell Support forever.
powerizer.. injector loop rear — bij Twin Motorcycles Buell Support forever.
needed to take out the front injector to get the connector off — bij Twin Motorcycles Buell Support forever.
tps wire hook up with a scotchlock pinch system.. crap connection — bij Twin Motorcycles Buell Support forever.
intake stacks on — bij Twin Motorcycles Buell Support forever.
spring clips back on, check if the stacks are mounted firmly.. try to pull theme off — bij Twin Motorcycles Buell Support forever.
mounting the idel air control hose with a ziptie — bijTwin Motorcycles Buell Support forever.
base plate on and k&N filter in — bij Twin Motorcycles Buell Support forever.
carefull with the 2008 models.. the fuel line is still plastic.. these break easy — bij Twin Motorcycles Buell Support forever.
setting the suspention.. and adding the fuel mapping— bij Twin Motorcycles Buell Support forever.
on with the neutral xb .. setting the clutch — bij Twin Motorcycles Buell Support forever.
with the rear wheel lifted , to check the primary chain.. wheel turns heavy.. belt was slipping over the pully... — bij Twin Motorcycles Buell Support forever.
the pully bearings are knackered and are seazed can not turn these — bij Twin Motorcycles Buell Support forever.
spiral clip out — bij Twin Motorcycles Buell Support forever.
and pressing out the brearings — bij Twin Motorcycles Buell Support forever.
new ones in and little neverseas on the spacers — bij Twin Motorcycles Buell Support forever.
mnnn ok belt is about gone.. need to call the owner— bij Twin Motorcycles Buell Support forever.
as this will not last very long anymore — bij Twin Motorcycles Buell Support forever.
ok for belt change.. take off the rear lower fender — bij Twin Motorcycles Buell Support forever.
wheel axle out.. so the wheel in on the thin piece off the axle — bij Twin Motorcycles Buell Support forever.
with the belt tension of, remove the swingarm brace— bij Twin Motorcycles Buell Support forever.
while you are here. check the wheel bearings — bijTwin Motorcycles Buell Support forever.
1e model belt.. most of these did not last this long — bij Twin Motorcycles Buell Support forever.
really gone.. next to breaking — bij Twin Motorcycles Buell Support forever.
cracked and old — bij Twin Motorcycles Buell Support forever.
new belt on — bij Twin Motorcycles Buell Support forever.
and swing arm brace on. before tightening the axle— bij Twin Motorcycles Buell Support forever.
checking the throttle cables — bij Twin Motorcycles Buell Support forever.
i give it a little lube.. they have been sticking in the cold — bij Twin Motorcycles Buell Support forever.
Xb12SCg.. dash and alarm light — bij Twin Motorcycles Buell Support forever.
we need to take the dash out for a new plate — bijTwin Motorcycles Buell Support forever.
screws need to come out in the back — bij Twin Motorcycles Buell Support forever.
cover can be pulled off — bij Twin Motorcycles Buell Support forever.
use some spoons or vorks to pull out the needles .. carefull — bij Twin Motorcycles Buell Support forever.
new dahs plate in — bij Twin Motorcycles Buell Support forever.
now cycle the dash , on off , so the dails are to zero— bij Twin Motorcycles Buell Support forever.
and press on the needles in the correct postion.. check this — bij Twin Motorcycles Buell Support forever.
and cover can go back on — bij Twin Motorcycles Buell Support forever.
and mounting back on the bike — bij Twin Motorcycles Buell Support forever.
connecting the hazerd light switch unit — bij Twin Motorcycles Buell Support forever.
works electronicly.. switch left and right in about 2 seconds and all indicator lights will blink — bij Twin Motorcycles Buell Support forever.