Articles & photos

Back

16-8-17 XB Wireharness, XR1200 Running, XB12Scg

20-9-2017 - What did we do today: 16-8-2017 Buell XB wire harness, XR1200X power upgrades, Buell XB12SCG finish neutral switch

moving the handle bar and the dash would go out on this XB , i want some leg room upfront so with the rear in the clamps — bij Twin Motorcycles Buell Support forever.

i want to take out the left front leg to have acces to the wire loom — bij Twin Motorcycles Buell Support forever.

scoop off — bij Twin Motorcycles Buell Support forever.

wheel and left leg out , there is the problem.. i hear the dash cycling when i tough the wire loom... — bij Twin Motorcycles Buell Support forever.

ok need some more room to fix this good , removing the cable guide — bij Twin Motorcycles Buell Support forever.

and stripping the loom — bij Twin Motorcycles Buell Support forever.

i will take out the cables here too.. so i have very good acces — bij Twin Motorcycles Buell Support forever.

nice bike.. in for a [ower upgrade :-) — bij Twin Motorcycles Buell Support forever.

grrrr..... how can you break a screw in the tank ring ?— bij Twin Motorcycles Buell Support forever.

same way to washers are mounted to 1 side , i think... — bij Twin Motorcycles Buell Support forever.

anyway fuel tank lifted a little and airfilter out — bij Twin Motorcycles Buell Support forever.

in the long run these will be come a issue on the stock filter boxes.. corrosion off the screws — bij Twin Motorcycles Buell Support forever.

k&N and flapper left in... ok.... difference will be big :-) — bij Twin Motorcycles Buell Support forever.

preping our HPA airbox — bij Twin Motorcycles Buell Support forever.

intake stack on the trottle bodie.. now a days i put a zip tie on it to hold it down better in the long run — bij Twin Motorcycles Buell Support forever.

hpa airbox on... nice.. still very prood off this one looks good and performs even better — bij Twin Motorcycles Buell Support forever.

getting some weight off ... rediculeus heavy stock exhaust — bij Twin Motorcycles Buell Support forever.

lucky number 1.... front header nuts... first tighten en release and WD40... and moving in and out , not to force the stud and breaking it — bij Twin Motorcycles Buell Support forever.

and lucky number 2 ... :-) — bij Twin Motorcycles Buell Support forever.

now the cover off to remove the stock bracket — bij Twin Motorcycles Buell Support forever.

flat gaskets in and new studs — bij Twin Motorcycles Buell Support forever.

comming to getter nice — bij Twin Motorcycles Buell Support forever.

seat unit off — bij Twin Motorcycles Buell Support forever.

to remove the rear stock exhaust brace — bij Twin Motorcycles Buell Support forever.

new plug.. and a tune for the XR... and test ride :-)very nice — bij Twin Motorcycles Buell Support forever.

wire harness fixed and mounting back — bij Twin Motorcycles Buell Support forever.

cables back in the dash — bij Twin Motorcycles Buell Support forever.

and opening the top end , as i dought the intake seals — bij Twin Motorcycles Buell Support forever.

every thing loose — bij Twin Motorcycles Buell Support forever.

and exhaust removed — bij Twin Motorcycles Buell Support forever.

the side stand was tighten by the customer... but still loose — bij Twin Motorcycles Buell Support forever.

neverseas... please bolts like this... no grease. or neverseas it need to be tight and stay tight... put locktite on it — bij Twin Motorcycles Buell Support forever.

engine down and replacing the intake seals , just ot be sure — bij Twin Motorcycles Buell Support forever.

engine up and mounting bolt to TQ specs — bij Twin Motorcycles Buell Support forever.

w-brace on and right side scoop back on — bij Twin Motorcycles Buell Support forever.

throttle cables in — bij Twin Motorcycles Buell Support forever.

and cover back on — bij Twin Motorcycles Buell Support forever.

letting here warm up.. to late for test ride.. will be to morrow — bij Twin Motorcycles Buell Support forever.

new front bolt... — bij Twin Motorcycles Buell Support forever.

front hanger flush to the exhaust and tighten every thing — bij Twin Motorcycles Buell Support forever.

rear axle loose 1 more time to mount the idler back— bij Twin Motorcycles Buell Support forever.

and chin spoiler back on , use loctite on these bolts.. so they don't rattel out — bij Twin Motorcycles Buell Support forever.

front wheel loose — bij Twin Motorcycles Buell Support forever.

bearings ok — bij Twin Motorcycles Buell Support forever.

tighen the caliper first .. helps when you notice the axle is cross threathing in the leg — bij Twin Motorcycles Buell Support forever.

now it turns in very easy — bij Twin Motorcycles Buell Support forever.

running for the first time in a few weeks... lost been done on this bike — bij Twin Motorcycles Buell Support forever.

needed to pull the clutch to start ... neutral light works.. but has allot off resistance — bij Twin Motorcycles Buell Support forever.

belt tension off again — bij Twin Motorcycles Buell Support forever.

belt off the front pully — bij Twin Motorcycles Buell Support forever.

5/8 ( or 16 mm ) high socket turned thinner at the end — bij Twin Motorcycles Buell Support forever.

under a light angle, and yo ucan unscrew the neutral switch — bij Twin Motorcycles Buell Support forever.

better with the new one — bij Twin Motorcycles Buell Support forever.

now starting at a puch off the buttom — bij Twin Motorcycles Buell Support forever.