Articles & photos

Back

11-8-2017 M2 belt XB9 intake seals XB12Scg

19-9-2017 - What did we do today: 11-8-2017 Buell M2 belt and tyres. Buell XB9 intake seals and throttle cables, Buell XB12Scg finish head

very nice M2... his 4e Buell.. :-) — bij Twin Motorcycles Buell Support forever.

in for Belt change.. as my new tool is not ready yet ( old one broke ) need to go the official route ( sort off ) and lift the frame off the engine , losening the tail— bij Twin Motorcycles Buell Support forever.

and fuel tank off — bij Twin Motorcycles Buell Support forever.

not really something you want to see on your belt — bij Twin Motorcycles Buell Support forever.

so rear off the bike in the straps to get the weight off— bij Twin Motorcycles Buell Support forever.

while we are here new rear tyre , wheel out.. needed to hammer the axle out all the way — bij Twin Motorcycles Buell Support forever.

mnnn — bij Twin Motorcycles Buell Support forever.

axle cleaned on the late.. with a coat off grease back in with the fresh rear tire — bij Twin Motorcycles Buell Support forever.

rear tiebar loose ( below the battery ) and top tie rod loose — bij Twin Motorcycles Buell Support forever.

normaly these are very tight.. but these where actualy loose — bij Twin Motorcycles Buell Support forever.

oil filter removed ma looking all the lines and cable are long enough , lifting the frame up to remove the right side isolator — bij Twin Motorcycles Buell Support forever.

sliding the new belt in — bij Twin Motorcycles Buell Support forever.

and on the pullies — bij Twin Motorcycles Buell Support forever.

frame down again , and isolators mounted.. tierod mounted — bij Twin Motorcycles Buell Support forever.

oil filter back on — bij Twin Motorcycles Buell Support forever.

tail section in position and fuel tank on — bij Twin Motorcycles Buell Support forever.

moving to the front for a new tire — bij Twin Motorcycles Buell Support forever.

preping ( loosening the cap and pin ) the caliper while it is mounted — bij Twin Motorcycles Buell Support forever.

brake pads out , with Torq bolts is loosen these — bijTwin Motorcycles Buell Support forever.

so i can take off the caliper with out damaging the wheel — bij Twin Motorcycles Buell Support forever.

fresh tyre on and tighten the caliper to 50 Nm — bij Twin Motorcycles Buell Support forever.

loctite on the axle and tighten the nut ... push down the suspention a few time and tighen the pich bolts— bij Twin Motorcycles Buell Support forever.

logn way from home.. leasking intake seals — bij Twin Motorcycles Buell Support forever.

Austria... first one in the shop ;-) — bij Twin Motorcycles Buell Support forever.

little precaustion to look at the front isolator , douse not have much life in it left — bij Twin Motorcycles Buell Support forever.

airfilter removed, and engine supported to lower the engine — bij Twin Motorcycles Buell Support forever.

and loosen the intake bolts ... cut off 1/4 inch allen works good — bij Twin Motorcycles Buell Support forever.

intake off, — bij Twin Motorcycles Buell Support forever.

now clean and check... new throttle cable is a must i believe they are bought half gone — bij Twin Motorcycles Buell Support forever.

intake on.. and engine back up — bij Twin Motorcycles Buell Support forever.

pulling through the new throttle cables — bij Twin Motorcycles Buell Support forever.

and mounting back on the base plate — bij Twin Motorcycles Buell Support forever.

new k&N filter and airbox mounted — bij Twin Motorcycles Buell Support forever.

checking the tps / idle and test ride :-) — bij Twin Motorcycles Buell Support forever.

XB12 Scg head.. head is back on — bij Twin Motorcycles Buell Support forever.

if the studs ahe a problem like this one, edm out and needed to do a timesert.. check the flanges.. a very slight off set can make the flange fit bad... drilling the holes a little bigger will make theme fit again — bij Twin Motorcycles Buell Support forever.

header on and front 02 sensor on — bij Twin Motorcycles Buell Support forever.

coil bracket — bij Twin Motorcycles Buell Support forever.

and intake manifold back ... much better with the big flanges but a pain to mount , because they are so big — bij Twin Motorcycles Buell Support forever.

engine back up and front mount to TQ — bij Twin Motorcycles Buell Support forever.

hooking up the cables — bij Twin Motorcycles Buell Support forever.

do the throttle cables before you finish.. so you can check if you can adjust theme right , as the stop in the manifold is flexible — bij Twin Motorcycles Buell Support forever.

lock clip on and tighten the cables — bij Twin Motorcycles Buell Support forever.

coil in — bij Twin Motorcycles Buell Support forever.

check the spark plug cables.. if the connectors are corroded.. replace theme — bij Twin Motorcycles Buell Support forever.