Articles & photos
Back |
30-6-2017 XB2X exhaust studs, XB12SS check
9-8-2017 - What did we do today 30-6-2017 Buell Xb12X exhaust studs, check up Buell XB12Ss
very clean Uly came in by road recovery — bij Twin Motorcycles Buell Support forever.
with a sort off rattle, front header flange is loose... 1 stud broken, the other nut rattled off ? — bij Twin Motorcycles Buell Support forever.
ok striping.. as we need to rotate the engine , scoops off — bij Twin Motorcycles Buell Support forever.
rear exhaust straps... when positioned right you can acces theme — bij Twin Motorcycles Buell Support forever.
mnnn front support is loose — bij Twin Motorcycles Buell Support forever.
loose front support has been ratteling for some time , cause / effect — bij Twin Motorcycles Buell Support forever.
anyway w-brace loose — bij Twin Motorcycles Buell Support forever.
and loosen the clutch cable — bij Twin Motorcycles Buell Support forever.
top side airbox removed and top tie rod loose , engine can be rotated down — bij Twin Motorcycles Buell Support forever.
been ratteling for a littel while , looking at the marks— bij Twin Motorcycles Buell Support forever.
out with the old gasket — bij Twin Motorcycles Buell Support forever.
and drill jig mounted — bij Twin Motorcycles Buell Support forever.
with the dril jigg, cobalt drills ( i made these longer ) easy ... still allot off work.. but get some very good dril bits.. they work — bij Twin Motorcycles Buell Support forever.
retapping the hole — bij Twin Motorcycles Buell Support forever.
and mounting the new stud.. note the lenght.. the thick flanges, calls for the studs to stick out further — bij Twin Motorcycles Buell Support forever.
new gasket and engine down for the last time for now — bij Twin Motorcycles Buell Support forever.
header mounted — bij Twin Motorcycles Buell Support forever.
engine up and front mount bolt to TQ — bij Twin Motorcycles Buell Support forever.
exhaust back under with new bolt — bij Twin Motorcycles Buell Support forever.
surten steps are good to follow, bolt not tight fully , strap also not tightened — bij Twin Motorcycles Buell Support forever.
first rear straps on tight — bij Twin Motorcycles Buell Support forever.
than tighten the front strap so the bracket sits flush on the exhaust.. than tighten the front bolt, and pipe clamp — bij Twin Motorcycles Buell Support forever.
covers back on — bij Twin Motorcycles Buell Support forever.
scoops on — bij Twin Motorcycles Buell Support forever.
and top tietod and air box mounted... — bij Twin Motorcycles Buell Support forever.
XB12SS check up — bij Twin Motorcycles Buell Support forever.
drain the oil when hot — bij Twin Motorcycles Buell Support forever.
new drain plug o-rings and new oil in — bij Twin Motorcycles Buell Support forever.
look and see when you are inspecting... exhaust clamp is loose — bij Twin Motorcycles Buell Support forever.
tightened it back on.. strange ? nor really normal that one ratels loose — bij Twin Motorcycles Buell Support forever.
rear wheel out — bij Twin Motorcycles Buell Support forever.
to checl the bearings .. these are ok — bij Twin Motorcycles Buell Support forever.
wheel back on , axle to 66 Nm — bij Twin Motorcycles Buell Support forever.
swapped around to the front — bij Twin Motorcycles Buell Support forever.
bearings feels good.. this one is also ok — bij Twin Motorcycles Buell Support forever.
wheel back in and set the caliper bolts to 50 NM — bij Twin Motorcycles Buell Support forever.
and refreshing the brake fluid — bij Twin Motorcycles Buell Support forever.
making noise while pulling the clutch — bij Twin Motorcycles Buell Support forever.
some home made easy clutch is mounted — bij Twin Motorcycles Buell Support forever.
but it is rubbing against the clutch spring when you pull the clutch — bij Twin Motorcycles Buell Support forever.
see the marks.. i bended the lever straight, problem was over — bij Twin Motorcycles Buell Support forever.