Articles & photos
| Back |
25-1-2017 Custom Xb12 wire harness
2-2-2017 - What did we do Today 25-1-2017 Custom Buell XB12 new wire harness
nice custom Xb12 2010 with osilating fuel pump , replacing the wire harness as this is modified so much that trouble shooting is about unpossible — bij Twin Motorcycles Buell Support forever.
hig beam and low beam switches — bij Twin Motorcycles Buell Support forever.
contact and start like a car — bij Twin Motorcycles Buell Support forever.
very nice speedo is mounted
2010 model have a front O2 sensor the wire is kept off the header with the clip
yeah having fun... what color wire
removing the tail section to have some room
start loosening all the sensors, as i want to test the new wire harness before i completely strip the bike
lights LED arrai mounted in the left scoop
crank sensor off
and sidestand switch..i will not mount this one back
could be handy if some one made a connector , commen problem with customs , wired from point to point with out connectors
going to make it a little better — bij Twin Motorcycles Buell Support forever.
top engine sensors connectors off
new harness
comes with relais and fuses
for now , ignition switch and right handle bar switch hooked up to the new wire harness
need to make some power extentions, but it works
and she is smootshing good, fuel pressure is stabile with out ocilating from way to low... so on with the removal off the harness
bike on a lift with a hoist, as i will lift the frame off the swing arm / engine — bij Twin Motorcycles Buell Support forever.
clutch cable loose from the lever — bij Twin Motorcycles Buell Support forever.
single wire throttle cable off
and TQ hammer exhaust off , to have a steady base to support the engine — bij Twin Motorcycles Buell Support forever.
Our Torque Hammer exhaust can be found here
2003-2007 also USA models 2003-2010
side stand off, to make it cleaner,
side stand, switch off
looks better like this.. and chin spoiler bracket will not go back on
the regulator wires where also ziptied to the w-brace, i will try to mount this back to the left scoop , so you will not notice these
supporting the bike — bij Twin Motorcycles Buell Support forever.
rear tiebar loose — bij Twin Motorcycles Buell Support forever.
and shock out — bij Twin Motorcycles Buell Support forever.
i will remove the breather oil line, to get to the startermotor wires — bij Twin Motorcycles Buell Support forever.
speed sensor out, and connection to the startermotor off — bij Twin Motorcycles Buell Support forever.
cooling fan out , as the wire harness runs through the frame opening — bij Twin Motorcycles Buell Support forever.
yep... wired from point to point... this one is cut — bij Twin Motorcycles Buell Support forever.
the battery is a LIon cel mounted in the swing arm, a extention is made and the cable is fed through the swing arm — bij Twin Motorcycles Buell Support forever.
craptactic.. and me wondering why the bike needed so much amps to start — bij Twin Motorcycles Buell Support forever.
ok front mount loose , front ens supported — bij Twin Motorcycles Buell Support forever.
in the straps to lift it up — bij Twin Motorcycles Buell Support forever.
mnnn ... weldon intake flanges — bij Twin Motorcycles Buell Support forever.
pulling the wire harnes out — bij Twin Motorcycles Buell Support forever.
need to look at the connections made so leave this a little to getter for now — bij Twin Motorcycles Buell Support forever.
replacing a wire harness you will need the plugs new — bij Twin Motorcycles Buell Support forever.
harness back in, little brace back in in the left rear off the frame, gearbox breather hose will go through also — bij Twin Motorcycles Buell Support forever.
as the bike also had a slight leak in the intake seals, and the weldon flange is really not something i would keep on the bike , intake seals.. — bij Twin Motorcycles Buell Support forever.
with the frame lifted... really not much work 
:-) — bij Twin Motorcycles Buell Support forever.
small signs off leaking on the seals ( vacuum bites )— bij Twin Motorcycles Buell Support forever.
not sure ho much time was spend making this old flange to fit the new style heads .. new flange is 8 euro — bij Twin Motorcycles Buell Support forever.
